Stainless Steel
Stainless Steel Bar & Rod
Round, flat, square and hexagonal bar, cold drawn or hot rolled.
Quote within 24 working hours · Certificate type stated on the quote
Ø 3 – 600 mm · — · 304 · 304L · 316 +7
Specification
Stainless Steel Bar & Rod — Full Spec Range
These are the ranges we can quote against today. Anything outside them is a mill enquiry, not a stock call — we will say which in the first reply.
| Thickness | Ø 3 – 600 mm |
|---|---|
| Width | — |
| Length | Up to 6,000 mm |
| Alloy grades | 304 · 304L · 316 · 316L · 303 · 410 · 420 · 430 · 2205 · 904L |
| Tempers | Cold drawn · Ground · Hot rolled · Forged |
| Standards | ASTM A276 · A479 · EN 10088-3 |
| Surface finish | Pickled · Sandblasted · Brushed · Mirror |
| Typical applications | Shaft · Fastener stock · Pump · Valve · Marine fitting |
What the mill checks
Four Numbers That Decide Whether This Ships
1 Gauge at nine points
Thickness is measured across the full width, not at one spot. A coil that is on gauge at the edge and 0.04 mm light at the center will still pass a lazy check.
2 Mechanical properties per heat
Tensile, yield and elongation pulled from the actual heat, not from a nominal table. On request the values are reported on a 3.1 certificate with the heat number; a 2.2 statement is available where that is all your file requires.
3 Surface under raking light
Roller marks, oil stain, scratch and edge burr are checked before packing. Coated product is checked for film build and color delta.
4 Packing for the voyage
Kraft plus PE film, steel-strapped pallet, edge protector, desiccant. Photos of the strapping and seal number sent before sailing.
Also compare
Related Categories
Stainless Steel Profile
Angle, channel, I-beam and special sections.
Section 20 – 200 mm · —
Stainless Steel Fittings & Flanges
Elbows, tees, reducers, flanges, fasteners and custom fabricated parts.
DN 15 – DN 600 · —
Stainless Steel Coil
Cold-rolled and hot-rolled coil in 200 / 300 / 400 series.
0.3 – 8.0 mm · 600 – 2,000 mm
Before you ask
Stainless Steel Bar & Rod — Questions That Come Up
Which alloy grades and tempers can you supply in Stainless Steel Bar & Rod?
Grades: 304 · 304L · 316 · 316L · 303 · 410 · 420 · 430 · 2205 · 904L. Tempers: Cold drawn · Ground · Hot rolled · Forged. If your grade is not on that list it is usually a mill enquiry rather than a no — send it and we will say which one, in the first reply.
What sizes does Stainless Steel Bar & Rod cover?
Ø 3 – 600 mm thick, — wide, Up to 6,000 mm. Quoted against ASTM A276 · A479 · EN 10088-3. Where a drawing names two standards, we confirm which one governs before the order, not after the inspection report.
What certificate comes with Stainless Steel Bar & Rod?
EN 10204 3.1 with the heat analysis and mechanical results, or 2.2 where that is what your file requires. Third-party inspection by SGS or BV is available. The certificate type is confirmed on the quotation, before you commit.
What is the minimum order for Stainless Steel Bar & Rod?
2 t for stocked flat-rolled. Below that we consolidate into a shared container, so the order still ships — it just waits for a sailing.
How fast do you quote Stainless Steel Bar & Rod?
Quotation within 24 hours on working days. We price grade, temper, gauge and quantity in one reply, and say which standard governs if the drawing names two.
Where does the Stainless Steel Bar & Rod come from?
From audited mills across 6 regions — Gongyi, Wuxi / Changzhou, Zouping / Binzhou, Foshan, Ningbo / Taizhou, Luoyang — each chosen for the process this product needs. You deal with one party; the mill allocation is our job, not yours.
Quote on Stainless Steel Bar & Rod
Send grade, temper, thickness and quantity. You get price, lead time, MOQ and certificate type in one reply.