Flat Rolled
Aluminum Tread / Checker Plate
Raised-pattern slip-resistant plate: five-bar, three-bar, diamond.
Quote within 24 working hours · Certificate type stated on the quote
1.0 – 8.0 mm · 600 – 2,000 mm · 1050 · 1060 · 3003 +3
Specification
Aluminum Tread / Checker Plate — Full Spec Range
These are the ranges we can quote against today. Anything outside them is a mill enquiry, not a stock call — we will say which in the first reply.
| Thickness | 1.0 – 8.0 mm |
|---|---|
| Width | 600 – 2,000 mm |
| Length | Up to 6,000 mm |
| Alloy grades | 1050 · 1060 · 3003 · 5052 · 5754 · 6061 |
| Tempers | H14 · H22 · H24 · H114 · T6 |
| Standards | ASTM B209 · EN 1386 · GB/T 3618 |
| Surface finish | Mill finish · Bright · anodized |
| Typical applications | Vehicle floor · Dock plate · Stair tread · Ramp · Cold-room floor |
What the mill checks
Four Numbers That Decide Whether This Ships
1 Gauge at nine points
Thickness is measured across the full width, not at one spot. A coil that is on gauge at the edge and 0.04 mm light at the center will still pass a lazy check.
2 Mechanical properties per heat
Tensile, yield and elongation pulled from the actual heat, not from a nominal table. On request the values are reported on a 3.1 certificate with the heat number; a 2.2 statement is available where that is all your file requires.
3 Surface under raking light
Roller marks, oil stain, scratch and edge burr are checked before packing. Coated product is checked for film build and color delta.
4 Packing for the voyage
Kraft plus PE film, steel-strapped pallet, edge protector, desiccant. Photos of the strapping and seal number sent before sailing.
Where it is used
Common End Uses for Aluminum Tread / Checker Plate
Marine & Shipbuilding
Mg-alloyed plate resists seawater and welds without losing strength. This is the series classification societies expect to see on hull plate.
Transport & Automotive
Weight reduction per body panel is the entire business case. Formability and weldability decide the grade.
Building & Curtain Wall
Facade work is a coating problem first and a metal problem second. PVDF film thickness and anodizing class are what the specifier checks.
Also compare
Related Categories
Aluminum Sheet & Plate
Rolled flat product from 0.2 mm foil stock to 200 mm plate.
0.2 – 200 mm · 600 – 2,200 mm
Aluminum Coil
Continuously cast or hot-rolled coil for roll forming and stamping.
0.2 – 8.0 mm · 600 – 2,200 mm
Aluminum Strip
Slit coil with controlled edge burr and camber.
0.1 – 3.0 mm · 10 – 1,600 mm
Before you ask
Aluminum Tread / Checker Plate — Questions That Come Up
Which alloy grades and tempers can you supply in Aluminum Tread / Checker Plate?
Grades: 1050 · 1060 · 3003 · 5052 · 5754 · 6061. Tempers: H14 · H22 · H24 · H114 · T6. If your grade is not on that list it is usually a mill enquiry rather than a no — send it and we will say which one, in the first reply.
What sizes does Aluminum Tread / Checker Plate cover?
1.0 – 8.0 mm thick, 600 – 2,000 mm wide, Up to 6,000 mm. Quoted against ASTM B209 · EN 1386 · GB/T 3618. Where a drawing names two standards, we confirm which one governs before the order, not after the inspection report.
What certificate comes with Aluminum Tread / Checker Plate?
EN 10204 3.1 with the heat analysis and mechanical results, or 2.2 where that is what your file requires. Third-party inspection by SGS or BV is available. The certificate type is confirmed on the quotation, before you commit.
What is the minimum order for Aluminum Tread / Checker Plate?
2 t for stocked flat-rolled. Below that we consolidate into a shared container, so the order still ships — it just waits for a sailing.
How fast do you quote Aluminum Tread / Checker Plate?
Quotation within 24 hours on working days. We price grade, temper, gauge and quantity in one reply, and say which standard governs if the drawing names two.
Where does the Aluminum Tread / Checker Plate come from?
From audited mills across 6 regions — Gongyi, Wuxi / Changzhou, Zouping / Binzhou, Foshan, Ningbo / Taizhou, Luoyang — each chosen for the process this product needs. You deal with one party; the mill allocation is our job, not yours.
Quote on Aluminum Tread / Checker Plate
Send grade, temper, thickness and quantity. You get price, lead time, MOQ and certificate type in one reply.