Flat Rolled
Aluminum Strip
Slit coil with controlled edge burr and camber.
Quote within 24 working hours · Certificate type stated on the quote
0.1 – 3.0 mm · 10 – 1,600 mm · 1050 · 1060 · 1070 +4
Specification
Aluminum Strip — Full Spec Range
These are the ranges we can quote against today. Anything outside them is a mill enquiry, not a stock call — we will say which in the first reply.
| Thickness | 0.1 – 3.0 mm |
|---|---|
| Width | 10 – 1,600 mm |
| Length | Coil, slit to width |
| Alloy grades | 1050 · 1060 · 1070 · 1100 · 3003 · 5052 · 8011 |
| Tempers | O · H14 · H16 · H18 · H22 · H24 |
| Standards | ASTM B209 · EN 485 · GB/T 8544 |
| Surface finish | Mill finish · Degreased |
| Typical applications | Transformer winding · Cable shield · Lamp cap · Radiator fin |
What the mill checks
Four Numbers That Decide Whether This Ships
1 Gauge at nine points
Thickness is measured across the full width, not at one spot. A coil that is on gauge at the edge and 0.04 mm light at the center will still pass a lazy check.
2 Mechanical properties per heat
Tensile, yield and elongation pulled from the actual heat, not from a nominal table. On request the values are reported on a 3.1 certificate with the heat number; a 2.2 statement is available where that is all your file requires.
3 Surface under raking light
Roller marks, oil stain, scratch and edge burr are checked before packing. Coated product is checked for film build and color delta.
4 Packing for the voyage
Kraft plus PE film, steel-strapped pallet, edge protector, desiccant. Photos of the strapping and seal number sent before sailing.
Where it is used
Common End Uses for Aluminum Strip
Transport & Automotive
Weight reduction per body panel is the entire business case. Formability and weldability decide the grade.
Building & Curtain Wall
Facade work is a coating problem first and a metal problem second. PVDF film thickness and anodizing class are what the specifier checks.
Packaging & Foil
Pinhole count, elongation and surface cleanliness are the three numbers that decide whether a foil runs on your line.
Also compare
Related Categories
Aluminum Foil
Household, container, pharmaceutical and capacitor foil.
0.006 – 0.2 mm · 100 – 1,700 mm
Aluminum Circle & Disc
Blanks for deep drawing into cookware and lamp shades.
0.3 – 6.0 mm · Ø 100 – 1,200 mm
Aluminum Tread / Checker Plate
Raised-pattern slip-resistant plate: five-bar, three-bar, diamond.
1.0 – 8.0 mm · 600 – 2,000 mm
Before you order
What Goes Wrong With Aluminum Strip — and How to Specify Around It
Failure modes
- Burr on Slit Aluminum StripWhy slit aluminum strip has edge burr: knife clearance, blade wear and temper. How burr height is measured and what to specify for transformer and fin stock.
- Pinholes in Aluminum FoilWhy aluminum foil gets pinholes: melt cleanliness, rolling oil filtration and thin gauge. How pinhole count is measured under ASTM B479 and GB/T 3198.
- Camber and Wavy Edge in Sheet & CoilWhy aluminum sheet and coil show camber or wavy edge, how it is measured under EN 485 and ASTM B209, and what to specify to keep it off your automatic line.
- All eight failure modes →
Before you ask
Aluminum Strip — Questions That Come Up
Which alloy grades and tempers can you supply in Aluminum Strip?
Grades: 1050 · 1060 · 1070 · 1100 · 3003 · 5052 · 8011. Tempers: O · H14 · H16 · H18 · H22 · H24. If your grade is not on that list it is usually a mill enquiry rather than a no — send it and we will say which one, in the first reply.
What sizes does Aluminum Strip cover?
0.1 – 3.0 mm thick, 10 – 1,600 mm wide, Coil, slit to width. Quoted against ASTM B209 · EN 485 · GB/T 8544. Where a drawing names two standards, we confirm which one governs before the order, not after the inspection report.
What certificate comes with Aluminum Strip?
EN 10204 3.1 with the heat analysis and mechanical results, or 2.2 where that is what your file requires. Third-party inspection by SGS or BV is available. The certificate type is confirmed on the quotation, before you commit.
What is the minimum order for Aluminum Strip?
2 t for stocked flat-rolled. Below that we consolidate into a shared container, so the order still ships — it just waits for a sailing.
How fast do you quote Aluminum Strip?
Quotation within 24 hours on working days. We price grade, temper, gauge and quantity in one reply, and say which standard governs if the drawing names two.
Where does the Aluminum Strip come from?
From audited mills across 6 regions — Gongyi, Wuxi / Changzhou, Zouping / Binzhou, Foshan, Ningbo / Taizhou, Luoyang — each chosen for the process this product needs. You deal with one party; the mill allocation is our job, not yours.
Quote on Aluminum Strip
Send grade, temper, thickness and quantity. You get price, lead time, MOQ and certificate type in one reply.