Flat Rolled
Aluminum Foil
Household, container, pharmaceutical and capacitor foil.
Quote within 24 working hours · Certificate type stated on the quote
0.006 – 0.2 mm · 100 – 1,700 mm · 1235 · 8011 · 8079 +3
Specification
Aluminum Foil — Full Spec Range
These are the ranges we can quote against today. Anything outside them is a mill enquiry, not a stock call — we will say which in the first reply.
| Thickness | 0.006 – 0.2 mm |
|---|---|
| Width | 100 – 1,700 mm |
| Length | Coil / jumbo roll |
| Alloy grades | 1235 · 8011 · 8079 · 8021 · 1100 · 1060 |
| Tempers | O · H18 · H22 · H24 |
| Standards | ASTM B479 · EN 546 · GB/T 3198 |
| Surface finish | One-side bright · Both-side bright · Lubricated · Annealed (degreased) |
| Typical applications | Food packaging · Pharma blister · Capacitor · Cable wrap · Insulation |
What the mill checks
Four Numbers That Decide Whether This Ships
1 Gauge at nine points
Thickness is measured across the full width, not at one spot. A coil that is on gauge at the edge and 0.04 mm light at the center will still pass a lazy check.
2 Mechanical properties per heat
Tensile, yield and elongation pulled from the actual heat, not from a nominal table. On request the values are reported on a 3.1 certificate with the heat number; a 2.2 statement is available where that is all your file requires.
3 Surface under raking light
Roller marks, oil stain, scratch and edge burr are checked before packing. Coated product is checked for film build and color delta.
4 Packing for the voyage
Kraft plus PE film, steel-strapped pallet, edge protector, desiccant. Photos of the strapping and seal number sent before sailing.
Where it is used
Common End Uses for Aluminum Foil
Packaging & Foil
Pinhole count, elongation and surface cleanliness are the three numbers that decide whether a foil runs on your line.
Cookware & Deep Drawing
Deep drawing is a ductility test. Purity and O-temper control decide whether the blank draws or tears.
Also compare
Related Categories
Aluminum Circle & Disc
Blanks for deep drawing into cookware and lamp shades.
0.3 – 6.0 mm · Ø 100 – 1,200 mm
Aluminum Tread / Checker Plate
Raised-pattern slip-resistant plate: five-bar, three-bar, diamond.
1.0 – 8.0 mm · 600 – 2,000 mm
Aluminum Sheet & Plate
Rolled flat product from 0.2 mm foil stock to 200 mm plate.
0.2 – 200 mm · 600 – 2,200 mm
Before you order
What Goes Wrong With Aluminum Foil — and How to Specify Around It
Failure modes
- Pinholes in Aluminum FoilWhy aluminum foil gets pinholes: melt cleanliness, rolling oil filtration and thin gauge. How pinhole count is measured under ASTM B479 and GB/T 3198.
- Thickness Out of ToleranceWhy aluminum arrives thinner than specified: minus-tolerance rolling and edge drop. How to write thickness tolerance into an order under ASTM B209.
- Telescoped or Loose CoilWhy aluminum coils telescope or collapse: winding tension, core strength and transport restraint. What to specify for coil ID, weight, core type and packing.
- All eight failure modes →
Before you ask
Aluminum Foil — Questions That Come Up
Which alloy grades and tempers can you supply in Aluminum Foil?
Grades: 1235 · 8011 · 8079 · 8021 · 1100 · 1060. Tempers: O · H18 · H22 · H24. If your grade is not on that list it is usually a mill enquiry rather than a no — send it and we will say which one, in the first reply.
What sizes does Aluminum Foil cover?
0.006 – 0.2 mm thick, 100 – 1,700 mm wide, Coil / jumbo roll. Quoted against ASTM B479 · EN 546 · GB/T 3198. Where a drawing names two standards, we confirm which one governs before the order, not after the inspection report.
What certificate comes with Aluminum Foil?
EN 10204 3.1 with the heat analysis and mechanical results, or 2.2 where that is what your file requires. Third-party inspection by SGS or BV is available. The certificate type is confirmed on the quotation, before you commit.
What is the minimum order for Aluminum Foil?
2 t for stocked flat-rolled. Below that we consolidate into a shared container, so the order still ships — it just waits for a sailing.
How fast do you quote Aluminum Foil?
Quotation within 24 hours on working days. We price grade, temper, gauge and quantity in one reply, and say which standard governs if the drawing names two.
Where does the Aluminum Foil come from?
From audited mills across 6 regions — Gongyi, Wuxi / Changzhou, Zouping / Binzhou, Foshan, Ningbo / Taizhou, Luoyang — each chosen for the process this product needs. You deal with one party; the mill allocation is our job, not yours.
Quote on Aluminum Foil
Send grade, temper, thickness and quantity. You get price, lead time, MOQ and certificate type in one reply.