Finished
Anodized Aluminum
Electrochemical oxide layer — Color is in the metal, not on it.
Quote within 24 working hours · Certificate type stated on the quote
0.3 – 8.0 mm · 600 – 1,600 mm · 1050 · 1060 · 1100 +3
Specification
Anodized Aluminum — Full Spec Range
These are the ranges we can quote against today. Anything outside them is a mill enquiry, not a stock call — we will say which in the first reply.
| Thickness | 0.3 – 8.0 mm |
|---|---|
| Width | 600 – 1,600 mm |
| Length | Coil, sheet or profile |
| Alloy grades | 1050 · 1060 · 1100 · 3003 · 5005 · 6063 |
| Tempers | H14 · H24 · T5 · T6 |
| Standards | ISO 7599 · AAMA 611 · GB/T 5237.2 |
| Surface finish | Natural · Black · Bronze · Champagne · Gold · Blue · Custom (5–25 µm) |
| Typical applications | Architectural trim · Elevator cab · Consumer electronics shell · Nameplate |
What the mill checks
Four Numbers That Decide Whether This Ships
1 Gauge at nine points
Thickness is measured across the full width, not at one spot. A coil that is on gauge at the edge and 0.04 mm light at the center will still pass a lazy check.
2 Mechanical properties per heat
Tensile, yield and elongation pulled from the actual heat, not from a nominal table. On request the values are reported on a 3.1 certificate with the heat number; a 2.2 statement is available where that is all your file requires.
3 Surface under raking light
Roller marks, oil stain, scratch and edge burr are checked before packing. Coated product is checked for film build and color delta.
4 Packing for the voyage
Kraft plus PE film, steel-strapped pallet, edge protector, desiccant. Photos of the strapping and seal number sent before sailing.
Where it is used
Common End Uses for Anodized Aluminum
Transport & Automotive
Weight reduction per body panel is the entire business case. Formability and weldability decide the grade.
Building & Curtain Wall
Facade work is a coating problem first and a metal problem second. PVDF film thickness and anodizing class are what the specifier checks.
Cookware & Deep Drawing
Deep drawing is a ductility test. Purity and O-temper control decide whether the blank draws or tears.
Also compare
Related Categories
Corrugated Aluminum Sheet
Roll-formed roofing and cladding profiles.
0.3 – 1.2 mm · Cover width 750 – 1,000 mm
Mirror Finish Aluminum Sheet
Polished to a specular reflectance above 85%.
0.2 – 3.0 mm · 600 – 1,300 mm
Perforated Aluminum Sheet
Punched round, slot or decorative hole patterns.
0.3 – 5.0 mm · 600 – 1,500 mm
Before you order
What Goes Wrong With Anodized Aluminum — and How to Specify Around It
Failure modes
- Anodizing Color VariationWhy anodized aluminum varies in color between batches: alloy drift, extrusion parameters and bath control. How film thickness and color are specified.
- All eight failure modes →
Specification guides
- Anodizing Film Thickness Classes: AA5 to AA25What anodizing classes AA5 to AA25 mean in microns, which class suits interior, architectural and coastal exposure, and how sealing is checked.
- All technical guides →
Before you ask
Anodized Aluminum — Questions That Come Up
Which alloy grades and tempers can you supply in Anodized Aluminum?
Grades: 1050 · 1060 · 1100 · 3003 · 5005 · 6063. Tempers: H14 · H24 · T5 · T6. If your grade is not on that list it is usually a mill enquiry rather than a no — send it and we will say which one, in the first reply.
What sizes does Anodized Aluminum cover?
0.3 – 8.0 mm thick, 600 – 1,600 mm wide, Coil, sheet or profile. Quoted against ISO 7599 · AAMA 611 · GB/T 5237.2. Where a drawing names two standards, we confirm which one governs before the order, not after the inspection report.
What certificate comes with Anodized Aluminum?
EN 10204 3.1 with the heat analysis and mechanical results, or 2.2 where that is what your file requires. Third-party inspection by SGS or BV is available. The certificate type is confirmed on the quotation, before you commit.
What is the minimum order for Anodized Aluminum?
It follows the base material — 2 t for stocked flat-rolled — plus the finishing run, which we price alongside it rather than as a separate order.
How fast do you quote Anodized Aluminum?
Quotation within 24 hours on working days. We price grade, temper, gauge and quantity in one reply, and say which standard governs if the drawing names two.
Where does the Anodized Aluminum come from?
From audited mills across 6 regions — Gongyi, Wuxi / Changzhou, Zouping / Binzhou, Foshan, Ningbo / Taizhou, Luoyang — each chosen for the process this product needs. You deal with one party; the mill allocation is our job, not yours.
Quote on Anodized Aluminum
Send grade, temper, thickness and quantity. You get price, lead time, MOQ and certificate type in one reply.