Finished
Mirror Finish Aluminum Sheet
Polished to a specular reflectance above 85%.
Quote within 24 working hours · Certificate type stated on the quote
0.2 – 3.0 mm · 600 – 1,300 mm · 1050 · 1060 · 1070 +3
Specification
Mirror Finish Aluminum Sheet — Full Spec Range
These are the ranges we can quote against today. Anything outside them is a mill enquiry, not a stock call — we will say which in the first reply.
| Thickness | 0.2 – 3.0 mm |
|---|---|
| Width | 600 – 1,300 mm |
| Length | Up to 4,000 mm |
| Alloy grades | 1050 · 1060 · 1070 · 1085 · 1100 · 5005 |
| Tempers | H14 · H16 · H18 · H24 |
| Standards | ASTM B209 · EN 485 · GB/T 3880 |
| Surface finish | Mirror (85–95% reflectance) · Brushed · PVC protected |
| Typical applications | Reflector · Lighting · Decorative trim · Solar reflector · Nameplate |
What the mill checks
Four Numbers That Decide Whether This Ships
1 Gauge at nine points
Thickness is measured across the full width, not at one spot. A coil that is on gauge at the edge and 0.04 mm light at the center will still pass a lazy check.
2 Mechanical properties per heat
Tensile, yield and elongation pulled from the actual heat, not from a nominal table. On request the values are reported on a 3.1 certificate with the heat number; a 2.2 statement is available where that is all your file requires.
3 Surface under raking light
Roller marks, oil stain, scratch and edge burr are checked before packing. Coated product is checked for film build and color delta.
4 Packing for the voyage
Kraft plus PE film, steel-strapped pallet, edge protector, desiccant. Photos of the strapping and seal number sent before sailing.
Where it is used
Common End Uses for Mirror Finish Aluminum Sheet
Cookware & Deep Drawing
Deep drawing is a ductility test. Purity and O-temper control decide whether the blank draws or tears.
Electronics & Heat Management
Heat sinks are an extrusion geometry problem: fin height, fin pitch and flatness tolerance. 6063-T5 holds fine fins that 6061 cannot.
Also compare
Related Categories
Perforated Aluminum Sheet
Punched round, slot or decorative hole patterns.
0.3 – 5.0 mm · 600 – 1,500 mm
Color Coated Aluminum
Coil or sheet pre-painted with PVDF, PE or epoxy.
0.2 – 4.0 mm · 600 – 1,800 mm
Aluminum Composite Panel
Two aluminum skins bonded to a mineral or PE core.
Panel 3 / 4 / 5 / 6 mm · 1,000 – 1,575 mm
Before you ask
Mirror Finish Aluminum Sheet — Questions That Come Up
Which alloy grades and tempers can you supply in Mirror Finish Aluminum Sheet?
Grades: 1050 · 1060 · 1070 · 1085 · 1100 · 5005. Tempers: H14 · H16 · H18 · H24. If your grade is not on that list it is usually a mill enquiry rather than a no — send it and we will say which one, in the first reply.
What sizes does Mirror Finish Aluminum Sheet cover?
0.2 – 3.0 mm thick, 600 – 1,300 mm wide, Up to 4,000 mm. Quoted against ASTM B209 · EN 485 · GB/T 3880. Where a drawing names two standards, we confirm which one governs before the order, not after the inspection report.
What certificate comes with Mirror Finish Aluminum Sheet?
EN 10204 3.1 with the heat analysis and mechanical results, or 2.2 where that is what your file requires. Third-party inspection by SGS or BV is available. The certificate type is confirmed on the quotation, before you commit.
What is the minimum order for Mirror Finish Aluminum Sheet?
It follows the base material — 2 t for stocked flat-rolled — plus the finishing run, which we price alongside it rather than as a separate order.
How fast do you quote Mirror Finish Aluminum Sheet?
Quotation within 24 hours on working days. We price grade, temper, gauge and quantity in one reply, and say which standard governs if the drawing names two.
Where does the Mirror Finish Aluminum Sheet come from?
From audited mills across 6 regions — Gongyi, Wuxi / Changzhou, Zouping / Binzhou, Foshan, Ningbo / Taizhou, Luoyang — each chosen for the process this product needs. You deal with one party; the mill allocation is our job, not yours.
Quote on Mirror Finish Aluminum Sheet
Send grade, temper, thickness and quantity. You get price, lead time, MOQ and certificate type in one reply.